Submissions     Contact     Advertise     Donate     BlogRoll     Subscribe                         

Wednesday, April 20, 2011

Make Your Own Gravity Fed Home Water Filtration System

Original Article


Note from Nick: Thanks to Cash for contributing this great article. I personally own the Royal Berkey system from Jeff “The Berkey Guy” at Directive 21 and think it is a great addition to any home from both a practical standpoint and aesthetic standpoint, however if you have been looking to make a quick little project and save some money this is a great way to make your own Berkey-Style water filter. Not to mention that home filtration is a basic prep I think everyone should have. If you end up getting the fitlers from Jeff over at Directive 21 please tell them that you are purchasing because of Save Our Skills and that would help to support the efforts of this website.


Thank you!
- Nick LaDieu

By Cash Olsen from KD5SSJ Solder Paste, Solder Tools and Solder Kits
I just made a water filtration system similar to the commercial units, cost about $100.
There is nothing real difficult, drills and hole saw. I have seen the details of a similar system, elsewhere. The major difference in my unit is that I used a Gamma lid in the top bucket for easy access to the filter elements and clean out of any silt and debris. The top bucket to bottom lid is carefully sealed with silicon caulk to make sure that no unfiltered water can dribble down the outside of the top bucket when being filled. The bottom bucket has a replacement spigot purchased for other water containers.
I purchased 4 sterasyl ceramic filter and installed two in this filter and will save two for future replacement. The filters are the same as used in the commercial units. Cost was $35 dollars each. So my total cost comes in right about $100. All the specifications of my bucket would also be the same as a commercial unit because the critical components are the same.
This was what my 5 gallon filter looks like.

This is the first bucket with the Gamma lid mounting ring attached. This should be done first because it must be driven on with a rubber mallet or hammer with wood to protect the ring from marring. This requires about 6 -7 sharp raps of the mallet around the ring with the lid removed.

This is the bucket with the Gamma lid in place. This should be removed for further assembly.
The next step is to mount a normal lid to the bottom of the bucket. This is rather critical. First apply a bead of silicon bathtub caulking around the inside recess of the lid so that when the bucket is set into it it will seal the bucket to the lid. Then apply another bead of silicon bathtub caulking around the bottom of the bucket just above the lid. This is important because you don’t want any contaminated water which might run down the side of the top bucket to be able to get into the lower bucket, that’s why it needs a very good water tight seal. Allow the silicon caulk to dry at least overnight, the instructions say that it is shower ready in 3 hours but this only means that the surface is skimmed over.

I measured 3″ from the center of the lid to the and marked two places, one on either side of the center. Use as small drill bit < 1/8″ (0.125″) and drill two pilot holes at each of the marked places. Drill as straight and perpendicular to the lid, as possible, through the lid and into the bottom of the bucket. Using the 1 1/2″ (1.50″) hole saw, picture 100_0117.JPG, enlarge the the whole in the bucket lid in both places. Using a 1/2″ (0.500″) drill bit drill two holes through the bottom of the bucket. The plastic lid and bucket are very easy to drill but be careful not to enlarge the 1/2″ hole size because this will only make it more difficult to seal the filter candle to the bucket in the next step.

From the top of the bucket mount the Sterasyl filters in the bucket. The rubber seal goes on the bottom of the filter and to the bottom of the bucket. Thread the wing nut onto the threads of the filter from the other side of the lid as shown in picture 100_0106 and tighten it good by hand. I used rubber gloves while installing the filter candles so as to avoid oils and other contaminants on the ceramic surface. There is a significant gap between the bottom of the top bucket and the lid, this is why it’s necessary to get a good seal and also the enlarged hole to give access to the wing nut.

shows the filter candles mounted in the top bucket. Picture 100_0112.JPG is a closer view of one candle mounted in the top bucket.

shows the bottom bucket with the drain cock, I have not yet mounted it at the time of this picture. Drill an appropriate hole for the grommet and mount it very near the bottom of the second (lower) bucket.

Shows the finished 5 gallon filter completed stack. I removed the locking ring and I have not yet determined if I want to seat the lid on the second bucket. I have found it to be very handy to be able to unstack the system and carry each bucket by it’s bail handle.
I purchased the buckets and lids (including Gamma lid) from BayTecContainers.com and I purchased the 4 x Doulton Super Sterasyl Ceramic Filter Candle 10″ @ $35.00 10 Long Mount W9121709 total including shipping was $141.99 from www.FiltersFast.com . I have a spare set of ceramic filters for replacement. I’m sure that there are other sources for all of the components.
Note from Nick: I talked with Cash and he agreed that Super Sterasyl Ceramic filters from Directive 21 was a better deal (saving about $10)
Follow the instructions with your filters candles for the initial use and restarting after prolonged lack of use.
Remove the Gamma lid to fill the top bucket and replace it loosely while the filtration is taking place. At the rate of 1 liter per hour (gravity feed) for each filter you should expect 5 gallons (18.9 liters) to take about 9 1/2 to 10 hours, or 10 gallons per day (two 5 gallon runs in 24 hours).
If you have any questions or suggestions, please leave a comment below.



1 comment:

  1. That's a great idea! A DIY water filter system at home. This way we can save money and ensure health for our family. For those who doesn't have enough time to make one you can buy those commercially produced.

    ReplyDelete